Sl-r11 manual

Current consumption mA max. Page 11 10 ms or less Supply voltage interruption Weight excluding dedicated brackets Approx. This eliminates having to redo the wiring each time the relay is replaced and limits wiring mistakes made during rewiring.

Mode switch setting method 1. Turn off the SL-R11 power. Use a screwdriver to remove the switch cover screws, and then open the switch cover. Page 18 0. Hook B About installation inside control panels Always leave at least 30 mm 1.

Page 24 Chapter 3 Mounting and Installation [2] When mounting on the wall with screws 1. Refer to the previous figure, and peel off the power supply connector seal. Refer to the previous, figure, and connect the two units. Slide the SL-U2 connection hooks to fasten the units together.

First loosen the terminal block screws, and then retighten the terminal block screws after inserting the signal cables.

Have a third-party certification organization UL, etc. In addition, when connecting one emergency stop switch to the E-STOP input terminal, the wiring is as shown below, so refer to the following wiring.

This feature is active when the total number of con- nected SL-R11 units is 4 or less. Page Maintenance 5. Use the restart input to reset the FSD output. Page 37 Chapter 6 Maintenance 6. Install the new relay circuit board in the SL-R11 and tighten the screws. Recommended tight- ening torque is 0. Standards and have received Canada-U. For details regarding the following standards, contact the third-party certification organization, such as UL. Confirm that the package includes the main unit SL-R11 and following accessories.

SL-PC5P 5m SL-PC10P cable. Manual Instruction See. Instruction See. Hole for mounting screw for M4. The SL-U2 is a power supply that completely satisfies the above requirements.

This will cause the FSD to turn on, allowing the cancellation of the start interlock status. Using this function prevents the machine from being automatically started when the power is turned on, or when the start switch, etc.

The FSD turns off when an obstacle interrupts the detection zone, and this function keeps the FSD turned off even after the obstacle is removed from the detection zone. This will cause the FSD to turn on, allowing the cancellation of the restart interlock status. This function prevents the machine from automatically starting even when the obstacle detected by the SL-C Series is removed from the detection zone, so after the safety check is completed, the machine can be restarted by pressing the start switch, etc.

E-STOP input refers to 2 normally closed signal inputs that are used to rapidly stop the machine when the emergency stop switch or similar button is operated. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Contents Safety Precautions 1. Safety Headings This instruction manual uses the following headings to display important safety information. Failure to follow the instructions may lead to death or serious injury.

Provides important precautions and restrictions for proper operation. Provides additional information for proper operation.

Provides useful information for proper operation. Provides reference pages. For such regulations, contact directly the regulatory agency responsible for occupational safety and health in your country or region. The responsible personnel must install the SL-R11 in strict compliance with such safety regulations. Perform an appropriate installation of the SL-R11 after conducting a sufficient risk assessment for the target machine.

Do not install the reset mechanism in a position where it can be operated within the hazardous zone. Building a safety system with just one of these systems cannot stop the machine due to a control output malfunction and can result in a serious accident, includ- ing serious injury or death to the machine operator.

If using the AUX relay as a relay output to build a safety system and stop the machine, it could result in the serious injury or death of the machine operator.

If another relay is used for replacement, the SL-C Series or SL-R11 might malfunction, or a serious accident causing the serious injury or death of the machine operator might occur. If the wiring is not done correctly for the machine, a serious accident, such as serious injury or death to the machine operator could result. Accessories Confirm that the package includes the main unit SL-R11 and following accessories.

Front view Front view. Electrical life: , times min. You can only view or download manuals with. Sign Up and get 5 for free.

Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file.